ESmoke (P/N EKP1000) $1,795.00
Click here to buy it now.

OEM EVAP-Approved Smoke Machine (Full-Feature Model)

Where There's Smoke, There's a Solution
Light a fire under leak diagnosis with the ATS ESmoke.

Our top of the line smoke machine comes with these great features:

• State of the art smoke machine with advanced microprocessor.
• Built of top quality materials with long-life, rust-resistant coating.
• Large, built-in, full range flow meter can be adjusted for 0.020, 0.040 and 0.080-inch leak tests. Use it to confirm the presence a leak and then to check a leak repair: no flow = no leak.
• Auto-correct EVAP pressure (O.E.M. recommended 14” H2O).
• Auto shut-off safety valve keeps gas fumes from leaking into your work area.
• Ultraviolet die helps find very small leaks fast.

Locate leaks all over the car:

• Use the same STAR EnviroTech, Inc. technology chosen by many OEMs to locate EVAP leaks.
• Find EVAP leaks with safe, OEM-approved tests that won't harm the vehicle warranty.
• Locate 0.020, 0.040-inch EVAP leaks with our special “Two-minute Drill” that gives you EVAP system pass-fail status in 120 seconds.
• Uses air, CO2 or nitrogen to find leaks.

Save time testing these common components:

• EVAP systems • Turbochargers • Vacuum lines • Brake booster lines • Vacuum brake boosters • Throttle assemblies • EGR valves • Injector o-rings and air shroud seals • Head gasket leaks • Exhaust systems • HVAC vacuum lines and controls • Air intake hoses and ducts • Leaking window and door seals • Vacuum-operated door lock actuators • Under Dash Leaks • Oil Leaks • MAP Sensor Leaks • and much more...

Tired of having leak detection eat so much of your valuable time? Find leaks faster,
and easier; bill for your results, not lost motion.

Stop EVAP Come Backs!

Features:

• 2-Year Warranty
• Utilizes OEM-approved licensed technology from STAR EnviroTech, Inc., the only technology designed for and capable of being used with nitrogen, for safer EVAP testing! Uses shop air for general purpose leaks
• Can connect right to tire inflation nitrogen generator
• Full-featured design; the same technology chosen by many OEMs for EVAP testing
• Simple control valve dial selects precise internal orifice calibration for .020" / .040". and "future"
• Patented UltraTraceUV® solution deposits a fluorescent dye at the exact location of the leaks and is the only dye approved by automakers, good for about 2-years of testing
• Two-minute Pass / Fail feature verifies .040" or .020" leaks in OBD-II vehicles
• Will not void OEM factory warranty
• Smoke out OBD-II EVAP codes
• User refillable
• A must tool for OBD-II EVAP testing & general purpose leak testing
• Microprocessor technology

Specifications:

• Height 15 in. (38.1 cm) • Supply Pressure 13 in./H2O (0.032 bar) • Width 8 in. (20.3 cm) • Supply Volume 15 LPM • Length 15 in. (38.1 cm) Operating Temp. Range 45ºF to 140ºF • Net Weight 23 lb. (10.4 kg) (7.2ºC to 60ºC) • Shipping Weight 26.5 lb. (12.0 kg) • Smoke Supply Line 10 feet (3m) • Power Supply 12 volts DC Power Supply Line 10 feet (3m) • Power Consumption 15 amps. • Remote Starter Cable 10 feet (3m)

Inert Gas Pack (P/N EKP1030) $179.00

• NEW Inert Gas Pack provides safer EVAP testing in a very portable kit. It provides all the power of a large gas cylinder but fits into the palm of your hand.
• Do about 25 EVAP tests per refillable 20 oz. cylinder. (This is liquid inert gas, which lasts much longer than a 20 oz. gas-only cylinder.)
• Meets SAE International technical papers inert gas recommendations
  (2008-01-0554 & 2007-01-1235) for EVAP system testing.
• Using air as the smoke carrier is not recommended when testing a fuel vapor (EVAP) system. Air can create a flammable fuel mixture in the vehicle's fuel tank.
• Automakers also require the use of an inert gas when testing an EVAP system.