|


If
these links do not work for you copy and paste the address below into your
email account, put receive or cancel updates in the subject line and press
send. This will automatically update your information in our database.
updates@automotivetestsolutions.com
_________________________________________________________________________________
EScope
Download and Installation of latest version - Rev 1.25:
For
detailed for instructions on installing the EScope update, click here.
Quick Start Instructions:
-
Download http://www.automotivetestsolutions.com/download/Setup_EScope_1.25.exe
(36MB) to your “My Documents” folder.
-
Double-click on the
downloaded file to install the EScope software. If the installer asks
you if it is OK to uninstall the existing version allow it to do so and
then run the installer again to install the new version.
-
Note that the EScope
program will only run if you have your computer connected to Escope hardware
with power on unless you run it in Demo Mode.
-
You must have the
DAQ driver installed to use the Escope, even if running in Demo Mode.
- If you are upgrading
from Rev 1.21 or older:
- When you run the
Setup program if the installer doesn't ask to uninstall the EScope allow
it to install but then run the setup program a second time to correctly
uninstall the old program. Then run it a third time to install the new
program.
- You'll also need
to upgrade your driver. See "Driver Download" at the bottom
of this page for driver details.
Revision History
(most recent version can be downloaded
above)
- 12/23/2009: Rev 1.25:
- Optimized to work
better with Windows 7.
- Added "Size
to 1024x574 (Netbooks)" option.
- Added Panel Close
(X).
- Added error popup
for battery low indicator.
- Added digital input
code to read battery low signal.
- Added process data
routine that allows adding offsets to data.
- Increased Buffer
Size.
- Added "Mark
Data (Page Up)" to Deep record.
- Changed colors
of "Mark Cam Shaft" and "Mark Cylinders" to faint
yellow and faint green.
- 9/23/2007: Rev 1.24:
- Added smoothing routine
to Measure & Deep Rec.
- Adding offset to Mark
Cylinders for pressure transducer measurements.
- Modified Deep record save
to warn if file saving to already exists.
- 5/24/2007:
Rev 1.23:
- Fixed problem where Demo
Mode would automatically get selected at startup or auto-restart if
DAQ board was not seen. Pop-up will now allow user to see error and
re-start or select demo mode.
- Changed Mark Cylinders
to be offset -25% of one division for pressure marking. This more accurately
divides up the cylinders when using the pressure sensor.
- Added Demo Mode button/indicator
to main tab.
- Added 1MS/s ranges for
EScope Pro.
- Changed default ranges.
4/25/2007:
Rev 1.22:
- First version to support
both the EScope and EScope Pro. Program will automatically detect and
setup for correct hardware at startup.
- Added setup wizard that
shows hookup schematics, just-in-time training videos for various sensors,
and allows setup file selection form tree of sensor/signal types.
- Added Pressure Sensor
Utilities: Automatic scaling for each ATS sensor type, ZERO button,
Measure tools for marking cylinders, and +/-5000.0 range setting to
cover all sensors.
- Added ? Help buttons and
help text tab for quick access to EScope help. Also changed manual to
Flash type.
- Changed labels on Timing
tab to match labels on scope.
- Added open circuit detection
code and indicators that display red borders around CH#s for open circuit.
- Changed custom setup folder
to "SetupsCustom" instead of "Setups". “Setups”
contains setup files that are not to be changed.
- Added colored text to
CH#s on Setup tab.
- Added Right and Left Tab
for Window Sizing
- Increased chart history
from 5k to 10k
- 5/11/2006: Rev 1.21:
- First version posted on
this update page.
Driver Download (needed
if first installation or if upgrading to Rev 1.22 from older version):
- Use the following links
to install the the NIDAQ driver.
- Use the following link to install the NIDAQ driver with MAX if you are having problems the core driver.
|
|
|
Automotive
Test Solutions is a multi-national award winning company for innovative
thinking that produces tool solutions to the automotive industries. Established
in 2001, ATS manufactures oscilloscopes, OBD II generic scan tools, ignition
analyzers, gas analyzers, misfire detectors, pressure transducers, re
programmers, engine simulators, diagnostic stands, and a number of high
tech training products to serve the automotive technician. Automotive
Test Solutions: Our name says it all. |
|
|
|
|
|
|
Copyright
© 2001-2010 Automotive Test Solutions, Inc.
Phone: 505-265-5077, Toll-Free: 800-572-6112, Fax: 866-422-2931
515 Wyoming SE Suite A, Albuquerque, NM 87123 |
|
|
|
|
|